Thursday , 21 November 2024

Team Associated TC6.1 Build – Step 15 – Anti-Roll Bars

CompetitionX Build Blog

Team Associated TC6.1 Build
Team Associated TC6.1 Build

The Build – Part 15
The anti-roll bars are a major tuning option for the TC6.1 (for all on-road cars, actually). Care must be taken to make sure that these bars are completely straight and are built exactly the same on the left and right sides.

Build Notes:
The TC6.1 comes with AE’s new H.D.R.C. (High Definition Roll Control) anti-roll bar system. Since the ‘bars’ are all the same length and color (only the thickness designates them now), AE has included some shrink tubing to help tell them apart. Shrink this heat tubing onto the bars before proceeding any further.

Team Associated TC6.1 Build - Step 120
Team Associated TC6.1 Build - Step 120
To start off this step, we will be building 4 anti-roll bar ballstuds and pivot mounts. It is extremely important that the distance between the base of the ball and the base of the ball cup are the EXACT same. Having these distances different can drastically change the way the anti-roll bar works.

Team Associated TC6.1 Build - Step 121
Team Associated TC6.1 Build - Step 121
Attach the assembled anti-roll bar ballstud/pivot mounts to the suspension arms as shown. Tighten the screws down, but make sure the pivot ball can swivel freely.

Team Associated TC6.1 Build - Step 122
Team Associated TC6.1 Build - Step 122
Insert the set screws into the anti-roll bar tubes. Do not tighten down all the way…just enough to keep them in place. A dab of loctite here is also recommended.

Team Associated TC6.1 Build - Step 123
Team Associated TC6.1 Build - Step 123
After you have heatshrunk the yellow tubing onto the anti-roll bars…

Team Associated TC6.1 Build - Step 124
Team Associated TC6.1 Build - Step 124
…insert them into the anti-roll bar tube as shown and secure with the set screws. The angle is pre-set and should ‘seat’ this way. If not, you might need to remove the anti-roll bar and re-install.

Team Associated TC6.1 Build - Step 125
Team Associated TC6.1 Build - Step 125
Slide the anti-roll bar pivot ball onto the end of each anti-roll bar rod and secure with a set screw. The end of the anti-roll bar should be flush with the end of the anti-roll bar pivot ball. A dab of loctite on the set screw is recommended.

Team Associated TC6.1 Build - Step 127
Team Associated TC6.1 Build - Step 127
Set the anti-roll bar assembly into place on the bulkheads and secure with the plastic anti-roll bar mounts as shown. Make sure the anti-roll bar tubes face up; you can tell they face up by the set screws facing up.

Team Associated TC6.1 Build - Step 126
Team Associated TC6.1 Build - Step 126
Pop the anti-roll bar cups onto the anti-roll bar pivot balls. Do this on all four suspension arms.

Part 16 – Installing the electronics.
Back to the Team Associated TC6.1 Build List

About Tony Phalen

Tony Phalen - As an avid RC enthusiast, Tony has been building, bashing and racing RC Cars for over 30 years. He has participated in every kind of surface racing events - 1/18 scale trucks, 1/10 scale TC, Rock Racers, Rally - if it had wheels, he's raced it! He's also worked on both sides of the industry fence; collaborating with many major manufacturers (as well as being a sponsored driver) to working for a high-profile industry magazine. During this time he has learned many tricks, tips and techniques and is sharing that knowledge on CompetitionX - the most informative RC website on the internet!

Check Also

ProTek RC Performance Servos | CompetitionX

ProTek RC Performance Servos | CompetitionX

ProTek RC has dropped three new performance servos for hardcore racing enthusiasts – the PTK-575, …