Team Associated B44.3 Build – Part 7 – Turnbuckles / Driveline

The Build – Part 7
In Part 7 of our Team Associated B44.3 build, we’ll be assembling the outer suspension parts, the turnbuckles and connecting the two together.

Build Notes:
None.

Building turnbuckles can be a pain in the butt, but thankfully there are a few tools that make this task easier. Duratrax offers this ball end driver that holds onto the ball cup, making it easier to screw onto the turnbuckle. There are also a myriad of quality turnbuckle wrenches on the market that will make this job easier. I’ve listed some at the bottom of this post.

The next step is to separate the turnbuckles. As you see, there are 4 2″ turnbuckles and 2 1.77″ ones. The 4 longer ones are for the front and rear camber while the 2 shorter ones are for the steering. Just make sure you use the right ones during the right steps.

Assemble the 6 turnbuckles as shown, using the lengths suggested in the manual. I started with these lengths but did manipulate them once I got running on the track. After you build them keep the separated; they are build as a left and right for their intended location.

Press a locknut into the bottom of the steering arm and screw the silver ball stud in. Don’t forget your foam thingy.

Press two bearings into each steering arm. Insert the crush tube in between them.

Slide your assembled front axle through the steering arm. Press the drive hex onto the axle, with the notches facing out, and secure it in place with the drive pin.

Assemble the pair of caster blocks as shown. Both blocks are the same, just be sure to build them as a left and right.

Carefully fit the two hat washers into position in the steering arm. They will fall out quite easily so be sure to keep the arm sideways at all times.

Slide the caster block into position, keeping an eye on the hat washers to make sure they stay in place. Secure the caster block with the pair of 7/16″ screws. Do not overtighten … the steering arm should swivel back and forth with ease.

Attach the steering arm assembly to the front arm by sliding the hinge pin into place. Secure the hinge pin with the 2-56 screw. Not the orientation of the steering arm.

Find your front camber link turnbuckle and pop them into place (you did keep them separate, right?).

Find your steering link turnbuckles and pop them into place as well. Make sure the notches in the turnbuckles are all facing the same way.

The rear hubs use molded camber link towers for adjustment. AE includes two of them; an A and a B tower. Grab both A towers (but keep the B’s in case you want to make any changes at the track).

Insert the bearings and crush tubes into the rear hubs.

Assemble your rear hubs as shown using the A towers.

Add 3 3/16 shims to the rear axle and slide it though the hub assembly, followed by another 3/16 shim and finally the roll pin.

Slide the 12mm clamping hex onto the shaft and key it to the roll pin. Use the 2-56 screw to pin the hex into place.

Attach your rear hub assembly to the rear suspension arm using the rear hinge pin. You’ll be adding a pair of wheelbase washers as well, both behind the hub. Use the 2-56 screw to capture the rear hinge pin.

Find your rear camber link turnbuckles and pop them into place, matching their direction to the front (using the notches).

Nice long step but we got a lot accomplished. Double check your suspension to make sure everything swings freely.

Here are a few items that will make this build (and future builds) a little bit easier.

Team Associated B44.3 Buggy Build – Part 1 – Differentials
Team Associated B44.3 Buggy Build – Part 2 – Gearboxes
Team Associated B44.3 Buggy Build – Part 3 – Steering
Team Associated B44.3 Buggy Build – Part 4 – Suspension
Team Associated B44.3 Buggy Build – Part 5 – Center Bulkhead
Team Associated B44.3 Buggy Build – Part 6 – Top Decks
Team Associated B44.3 Buggy Build – Part 7 – Turnbuckles / Driveline
Team Associated B44.3 Buggy Build – Part 8 – Anti-Roll Bars
Team Associated B44.3 Buggy Build – Part 9 – Shocks
Team Associated B44.3 Buggy Build – Part 10 – Electronics
Team Associated B44.3 Buggy Build – Part 11 – Wheels, Tires and Body

Back to the Team Associated B44.3 Buggy Build List