Team Associated B5M Build – Part 7 – Electronics

Tony Phalen January 7, 2015 RC Build Blog - Team Associated B5M Build 1,132 Views

The Build – Part 7
Time to install the blood of the B5M, the electronics. We will be installing a Futaba S9350 Digital Servo, LRP Flow WorksTeam Brushless ESC, LRP X20 8.5T Brushless Motor and TrakPower 2S 5800mAh 90C 7.4v LiPo Battery. Time to mount it all up!

Build Notes:
The B5M allows the use of shorty- or brick-style LiPo batteries. I’m using a TrakPower brick pack, but if you decide to use any of the shorty LiPos on the market, AE has included a few foam spacers to help position the battery in the tray. You can also use these spacers to shift the battery front-to-back for weight distribution.

Team Associated B5M Build – Part 85 — Team Associated B5M Buggy Build Step 85

Here’s the gear that will be going into our B5M. Mucho modified power with a stout servo to keep it running straight.

Team Associated B5M Build – Part 86 — Team Associated B5M Buggy Build Step 86

Attach the servo mounts and steering arm to the servo (use the silver washers here even though the manual says ‘gold washers’). AE has provided us (FINALLY) with a solid drag link … no more fiddling with a lame setscrew. You’ll also notice that the servo mounts don’t extend to the bottom of the servo. Yup, new servo install design as well.

Team Associated B5M Build – Part 87 — Team Associated B5M Buggy Build Step 87

Feed the servo lead through the slot in the chassis and then drop the servo into place. You’ll see that it mounts from the top now instead of from underneath the chassis. Pop the drap link onto the steering bellcrank and you’re good to go!.

Team Associated B5M Build – Part 88 — Team Associated B5M Buggy Build Step 88

Slide the motor into the mount and secure with the M3x8mm screws (and washers). Attach your pinion gear (we’re using a 21T with the 8.5T motor) and set the gear mesh.

Team Associated B5M Build – Part 89 — Team Associated B5M Buggy Build Step 89

Attach the gear cover and slipper clutch cap.

Team Associated B5M Build – Part 90 — Team Associated B5M Buggy Build Step 90

Install the receiver and ESC into the chassis. Wire up your ESC wires and sensor wire. The B5M chassis has antenna mounting locations on both sides, allowing you to mount your receiver and ESC in a few different configurations. Peel and stick the battery foam pads onto the chassis and side rails as shown.

Team Associated B5M Build – Part 91 — Team Associated B5M Buggy Build Step 91

Slide your battery into place and attach the battery strap. Slide a red o-ring over the battery strap thumbwheel and attach. You can wire up your positive and negative battery terminals now as well.

Team Associated B5M Build – Part 92 — Team Associated B5M Buggy Build Step 92

Finally, attach the rear body mount pegs. After using these a few times, I may pull them off. The body sits so tight that it’s a little difficult to pull the body off. I may be using some Velcro in the near future.

Power up your transmitter and car and see if everything works. Off to the final completion steps.

Team Associated B5M Buggy Build – Part 1 – Steering
Team Associated B5M Buggy Build – Part 2 – Front Suspension
Team Associated B5M Buggy Build – Part 3 – Rear Suspension
Team Associated B5M Buggy Build – Part 4 – Transmission
Team Associated B5M Buggy Build – Part 5 – Axles & Turnbuckles
Team Associated B5M Buggy Build – Part 6 – Shocks
Team Associated B5M Buggy Build – Part 7 – Electronics
Team Associated B5M Buggy Build – Part 8 – Body, Wheels & Tires