CompetitionX CompetitionX is the most up-to-date source for RC Car News, Reviews and Videos for Radio Control. We also have the most comprehensive Manual Database on the web.
The rear bulkhead on the Tekno EB410.2 is very similar to the front, minus the steering. Most of the steps are the same, so we’ll only briefly cover those.
Build Notes:
Since Tekno has moved the rear shocks to the front of the arms, they rear anti-roll bar has to be relocated. The bar (and mounting system) will attach to either side of the rear bulkhead, so make sure you mount it to the CORRECT side during the build.
Since Tekno has moved the rear shocks to the front of the arms, they rear anti-roll bar has to be relocated. The bar (and mounting system) will attach to either side of the rear bulkhead, so make sure you mount it to the CORRECT side during the build.
Step 1:
Press the pair of bearings into the front bulkhead. Slide the pinion gear into place, then slip the outdrive over the pinion gear shaft. Secure in place with the M4 grub screw. A drop of threadlocker here is suggested.
Press the pair of bearings into the front bulkhead. Slide the pinion gear into place, then slip the outdrive over the pinion gear shaft. Secure in place with the M4 grub screw. A drop of threadlocker here is suggested.
Step 2:
Attach the anti-roll bar mount to the bulkhead. Note the orientation.
Attach the anti-roll bar mount to the bulkhead. Note the orientation.
Step 3:
Add a liberal amount of black grease to the rear diff gear. Slip 2 10×15 bearings onto the diff, then drop it into the rear bulkhead. Attach the bulkhead cap. Do not overtighten the lower screws – tighten down, then back off about 1/4 turn. Make sure the diff spins freely.
Add a liberal amount of black grease to the rear diff gear. Slip 2 10×15 bearings onto the diff, then drop it into the rear bulkhead. Attach the bulkhead cap. Do not overtighten the lower screws – tighten down, then back off about 1/4 turn. Make sure the diff spins freely.
Step 4:
Attach the bottom bulkhead plate.
Attach the bottom bulkhead plate.
Step 5:
Attach the stopper to the rear anti-roll bar. Do not overtighten the grub screw.
Attach the stopper to the rear anti-roll bar. Do not overtighten the grub screw.
Step 6:
Assemble the anti-roll bar ends. Line the ball ends with the end of the bar, then secure with the grub screw. A light drop of threadlocker is suggested here.
Assemble the anti-roll bar ends. Line the ball ends with the end of the bar, then secure with the grub screw. A light drop of threadlocker is suggested here.
Step 7:
Pop the threaded ball ends into place. Note the orientation.
Pop the threaded ball ends into place. Note the orientation.
Step 8:
Set the anti-roll bar in place and capture with the mount. Make sure the stopper on the bar fits in the groove.
Set the anti-roll bar in place and capture with the mount. Make sure the stopper on the bar fits in the groove.
Thread the grub screws in until they touch the anti-roll bar, then back off slightly. You want the bar to move freely without being hindered by the screws.
And now your rear bulkhead is done. Keep this handy as we’re about to work on the rear suspension.
Use the links below to follow each step.
Tekno RC EB410.2 4WD Buggy Build – Opening Page
Tekno RC EB410.2 4WD Buggy Build – Part 1 – Differentials
Tekno RC EB410.2 4WD Buggy Build – Part 2 – Steering/Front Bulkhead
Tekno RC EB410.2 4WD Buggy Build – Part 3 – Rear Bulkhead
Tekno RC EB410.2 4WD Buggy Build – Part 4 – Rear Suspension
Tekno RC EB410.2 4WD Buggy Build – Part 5 – Front Suspension
Tekno RC EB410.2 4WD Buggy Build – Part 6 – Chassis Assembly
Tekno RC EB410.2 4WD Buggy Build – Part 7 – Shocks
Tekno RC EB410.2 4WD Buggy Build – Part 8 – Electronics
Tekno RC EB410.2 4WD Buggy Build – Part 9 – Final Assembly
Tekno RC EB410.2 4WD Buggy Build – Opening Page
Tekno RC EB410.2 4WD Buggy Build – Part 1 – Differentials
Tekno RC EB410.2 4WD Buggy Build – Part 2 – Steering/Front Bulkhead
Tekno RC EB410.2 4WD Buggy Build – Part 3 – Rear Bulkhead
Tekno RC EB410.2 4WD Buggy Build – Part 4 – Rear Suspension
Tekno RC EB410.2 4WD Buggy Build – Part 5 – Front Suspension
Tekno RC EB410.2 4WD Buggy Build – Part 6 – Chassis Assembly
Tekno RC EB410.2 4WD Buggy Build – Part 7 – Shocks
Tekno RC EB410.2 4WD Buggy Build – Part 8 – Electronics
Tekno RC EB410.2 4WD Buggy Build – Part 9 – Final Assembly
