Monday , 31 March 2025

Tekno RC Announces Their New EB48 Electric 1/8th 4WD Buggy

Tekno RC Announces Their New EB48 Electric 1/8th 4WD Buggy
Tekno RC Announces Their New EB48 Electric 1/8th 4WD Buggy

Tekno RC has released info about their new, ground up EB48 1/8 4WD E-Buggy. This buggy has been 100% designed and tested in Southern California against some of the best drivers in the world. Check out these features:

Chassis:
• Designed to be electric from the ground up – no nitro conversions here!
• 4mm CNC 7075 aluminum hard anodized lightened chassis.
• Super narrow chassis – widest point is only 125mm (less than 5”) mudguard-to-mudguard.
• Class leading front and rear clearance (short chassis overhang) provides better bump handling and jump landing.
• Integrated battery tray/mud guard, battery is sunken into chassis for a super low COG.
• Integrated electronics tray/mud guard for easy removal of electronics.
• Spacious, enclosed, easy access radio box with integrated transponder mount.
• Single pack configuration is better balanced, lighter weight, and makes battery changes easier. Battery tray accommodate 2x2s packs.
• Adjustable chassis brace system for fine tuning flex with front, center, and rear braces.

Differentials and Drivetrain:
• 3 fluid filled adjustable super lightweight diffs.
• Less rotating mass = better acceleration.
• Straight center driveline for maximum efficiency and minimal wear.
• CV driveshafts with captured pins on all 4 wheels.

Shocks:
• Super smooth 16mm big bore shocks.
• 5mm CNC 7075 aluminum shock towers are standard.
• Innovative cone piston design (not just tapered) provides varied compression and rebound rates.
• Fully adjustable long travel suspension geometry maximizes stability and traction while providing superior cornering and on-power steering.
• CNC threaded shock bodies, caps, cartridge caps, and adjustment nuts.
• 4mm hardened steel polished shafts.
• Triple guide design for true consistent shaft action.
• Options for vented cap, emulsion, or standard shock configurations.
• Optional spring rates and spring kits are available.

Suspension and Steering:
• Adjustable length rear arms to suit any track condition.
• Adjustable front arm sweep and angle to make the car more aggressive (swept forward), or easier to drive (swept back).
• Front and rear arms can be used on either side, rear hubs can be used on either side – less parts in your toolbox.
• ‘Narrow pivot’ steering posts provide ‘0 bump’ geometry with almost ‘0 steering slop’.
• Adjustable CNC 7075 hinge pin braces are standard.
• 4mm inner, 3.5mm outer hinge pins, polished for smooth action.
• Adjustable Ackerman and bump-steer (bump in, 0 bump, bump out).
• CNC aluminum Ackerman plate rides on 4 precision bearings.
• LCG rod ends and lightweight turnbuckles are lowered by 5mm.
• Front/rear sway bars are the same length = less parts in your toolbox.
• Adjustable steering stops for precise steering travel settings.

Motor Mount:
• 2-piece CNC aluminum motor mount with precise dual clamping gear mesh adjustment.
• Lightweight direct-to-diff mount design.
• Use standard MOD 1 pinion, Tekno RC Traktion Drive or Elektri-Clutch.
• Use motor brakes or mechanical brakes, the choice is yours.
• Easily accommodates ‘Truggy’ or ‘Long’ can motors up to 78mm long.

Other Features:
• Lightweight easily adjustable wing mount system.
• High downforce wing included.
• Easily adjust anti-squat, rear toe, front arm angle, front arm sweep, roll center, toe, camber, wheelbase, rear arm length, Ackerman, bump steer, suspension geometry out of the box..
• Full set of option parts avaialble.
• Extremely easy to work on with minimal screw count.
• All metric hex hardware.
• 7.5lb RTR weight with common electronics and options.
• Sub-7lb running weight easily achievable

Specifications:
Length: 435mm (without wing)
Wheelbase: 323-335mm
Width: 306-310*mm (*optional hubs required)
Weight: 3400g (7.5lb) (RTR weight equipped w/ Tekin RX8, 600g battery, rx, etc)
Diff Ratio: F/R – 10/40t, Center – 44t
Battery tray dimensions: 50x148mm (2x2s or 1x4s config)
Kit/RTR: Kit

Needed to Complete:
• 2/3 channel radio/transmitter
• 1/8 Scale ESC and motor
• High torque steering servo, optional brake servo
• Pinion or Traktion Drive / Elektri-Clutch system
• 4-6s LiPo battery
• 1/8th scale buggy tires, wheels & CA glue
• Paint for body
• Hex tools (1.5, 2.0, 2.5mm), pliers, other tools

[source: www.teknorc.com]

About Tony Phalen

Tony Phalen - As an avid RC enthusiast, Tony has been building, bashing and racing RC Cars for over 30 years. He has participated in every kind of surface racing events - 1/18 scale trucks, 1/10 scale TC, Rock Racers, Rally - if it had wheels, he's raced it! He's also worked on both sides of the industry fence; collaborating with many major manufacturers (as well as being a sponsored driver) to working for a high-profile industry magazine. During this time he has learned many tricks, tips and techniques and is sharing that knowledge on CompetitionX - the most informative RC website on the internet!

Check Also

ProLine Lightweight Sprint Car Body Panel Set

ProLine Lightweight Losi 22S Sprint Car Body Panel Set

Hot on the tails of the new Losi 22S Sprint Car release, ProLine is bringing …